Browse

The atmospheric sound waves with frequencies lower than 20Hz are named infrasound waves. Among the multitude of infrasonic signals that have been recorded and detected during time, some of them have been associated with different natural or anthropogenic sources and the source of many other remaining hidden and unknown. At the beginning of year 2013, a permanent infrasound monitoring system composed by a MB AZEL2007 microbarometer, the digitizer and the transmitting equipment, was installed by NIEP, at Mangalia, R...

The Power Plant Rybnik (Elektrownia Rybnik) is one of many in Poland, which is coal-fired. Fly ash, as is well known, are combustion by-products, which are mineral residue from burning coal. Their phase composition depends mainly on the quality of fuel (coal) and combustion conditions. In the mineral composition of the examined ashes one has identified minerals such as: glaze, quartz, mullite, spinels, hematite, and unburnt coal. Spinels present in the fly ash can be a source of some metals, and due to the magneti...

This study comprehends the stability assessment of seven slopes with Pre-Cambrian rocks and located in traffic-access areas of SW Angola, one (Slope 1) is located on the road access from Lubango to Tundavala Gorge, another slope belongs to the CaholoпїЅs area near Humpata (Slope 2) and five of them (Slopes 3 to 7) are located on the LebaпїЅs Sierra, along the sinuous hair-pinned sections of the National Road 280. Slope 1 is composed by quartzites, volcanic rocks and lutites. Slope 2 shows sandstones, lutites and q...

The problem of atmospheric air pollution attracts great attention of ecologists and physicians because the protection of the environment and population health has a socio-economic significance. Oxides of nitrogen and carbon, methanol, phenol, formaldehyde, ammonia, chlorine hydride and suspended particulate matters (dust, soot) are the main anthropogenic air pollutants in Tomsk city. The main task of the air pollution monitoring is to identify sources of pollutant emissions. Stable isotope ratio analysis of the li...

The article is devoted to newly prepared methodology for survey, georeferencing and display of buildings in 2D and 3D, which is processed within the project "Omega 3" with support from the Technology Agency of the Czech Republic. The methodology is to establish a standardized output of geodetic surveying the interior and exterior of buildings, applicable to all types of buildings (residential, commercial, office, industrial, agricultural, equipment and infrastructure, rentals, recreational spaces) in order to ensu...

The current demand for energy production in dissipated systems and the related need for miniaturization of power machines require the use of appropriate technical solutions. Increasingly, power generation microsystems are used to produce electricity that functions in hermetic circuits (e.g. ORC - Organic Rankine Cycle). Rotors of such type of machinery, in order to generate the expected amount of energy, must rotate at speeds up to 100,000 rpm. Rotational speeds of this order represent significant problems in the ...

Steganography is part of security science that deals with art of data hiding. Modern steganography can serve as an effective tool for hidden data transfers or watermarking for various computer formats, like JPEG, PNG, and MPEG. But it can be misused for stealing data or information transfer in illegal activities too. Most of today available steganography tools are free for use with easy user interface. This significantly increases the risk of exploiting in business sector. Revealing this data is very difficult and...

In this study are presented and analyzed data resulted from monitoring of ions concentration: NO??, NO?? and PO?пїЅ? in surface waters from Bucharest during 2013 пїЅ 2016 period. The concentrations of these ions are an important indicator of the degree of eutrophication of lakes. The monitored surface waters are formed of 12 lakes rezulted by systematizing of Colentina River. The sources of pollution with nitrates and phosphates are coming from economic activities around lakes, from urban transport, and the initia...

This article is referring to a short study regarding the energy efficiency status in retail industry in Romania, in particular an analysis of the big sizes commercial buildings in this matter. It contains data which will allow us to compare an existing building with the industry norms in terms of the energy consumption and energy costs. Additionally, there are some recommendations provided to be taken care of in the near future for controlling energy better, using energy in a more efficient way and reducing avoida...

Russia is one of the most important players in the Arctic Zone with significant economic, security and political interests on these territories. This is primarily because of significant natural resources, in particular oil and gas, in the Russian Arctic. The objective of this paper is to define the main prospects of strategic development of the Russian Arctic zone, and to offer socioecological approach to its development. Arctic has considerable strategic importance to the Russian economy. Strategic development of...

The paper examines the various developments regarding strategic management of raw materials on national, European and international levels. The problems linked to this subject are of increasing importance for the producing industry. Thus it is necessary to act quickly and pursue a sustainable raw material policy. The main purpose of this work is to analyze the possibility of fly ash utilization for the road construction and possible application in other industry branches with interest. The methodology used in the ...

The пїЅameli Formation extensively outcrops in Denizli-Mu?la and Antalya (SW Turkey). In this study, the stratigraphy and ostracod assemblages of the пїЅameli Formation was studied. The пїЅameli formation is first defined in the пїЅameli Basin (Denizli) which is one of the grabens formed in Pliocene. The пїЅameli Formation consists mainly of lacustrine sandstone, marl and claystone and shows prominent terrestrial sedimentary features. In the field, the formation was observed as two different facies: Facies 1: disp...

The active stress pattern in the Apuseni Mts area is investigated and studied in relation to the local seismicity and geology. Our analysis is based on several high quality and resolution data bases obtained recently in the context of national and international projects and which refers to digital seismograms recorded by dense networks, parametric earthquakes catalogues and catalogues of focal mechanisms. The reduced stress tensor has been obtained by formal inversion of 89 focal mechanisms solutions. The maximum ...

In constructing the marine pipelines, the concrete weight coated pipes are used to create a negative buoyancy coating and its protection from the external mechanical damages produced by icebergs, trawl nets, anchors, dropped objects. So far, no requirements have been formulated for the determination of the stress-strain state of the concrete weight coated pipes laid using the stinger (S-lay) system. The structural analysis carried out in accordance with the standard requirements does not account for the negative b...

Faults can act both as seal and as pathways for fluid migration and therefore correct evaluation of fault zone properties is one of key element for conventional hydrocarbon reservoir management. Nevertheless, the unconventional plays deformed by faults became increasingly in demand for petroleum industry. Lower Paleozoic sediments in central part of Baltic Basin are considered as potential unconventional shale gas system. Key TOC-rich intervals in the area of interest are Caradoc Sasino Formation and Lower Llandov...

Previous researches have shown the possibility of using organic-mineral additive based on glyoxal for injection strengthening of soils in roadbases and engineering communications. Saponite containing material was used as mineral component in the composition. Saponite containing material is a solid phase, extracted from the circulating water suspension of the kimberlite ore dressing. Modification of the sandy soil by the tailored organic-mineral additive content increases its specific cohesion up to 50 times. It wa...

The main aim of case study is to compare changes in landscape structure between the years 1958 - 2009 in territory of the old industrial city Krompachy in Middle SpiпїЅ in Slovakia. The assessment of the spatial structure the classes of the land cover has significance especially for the research of landscape especially from the aspect of the maintaining landscape ecological stability and the sustainable development as well as the landscape potential. Land cover reflects the physiognomy of landscape, utilisation of...

The e-learning system eLogika serves for teaching logic. In the system there are study materials at studentsпїЅ disposal, but it also provides online tests and promotes all the activities in which the students can obtain their credits. The system collects data about users who are logged in, e.g. time spent on a particular activity, the number of activities performed by particular students, what data is a student interested in, etc. The goal of this paper is to describe the application of many-valued formal concept...

Water serves as a medium for fundamental process phases (e.g. tanning and dyeing) in leather production. The reduction of water consumption per product unit has been an environmental priority for European tanners over the years. This is possible mainly through the setting of continuous improvement objectives aiming at developing water efficient processes and water recycling technologies. The paper analyses the pickling operation, for bovine hides processing. The aim is to develop an automation system which will re...

The most important duties of the marine engines supervisors regarding to the operation of diesel marine engines is maintaining the serviceability of cylinder liners and piston rings of ship engines which includes extremely important process of running in piston rings an liners running after overhauling. During this process proper engine load to be maintained. and cylinder liners lubrication to be properly adjusted. This process can better monitored to avoid mistakes with procedures and can reduce cylinder lubricat...

The study aimed to evaluate the variability of some morphological characters and the correlations between these at black pine. The biological material was represented by four populations of black pine, two of southwestern Romania (Herculane and Svinita) and two of central Greece (Kerasia Evia and Ano Polidrosos). The experimental data were collected by biometric measurements conducted "in situ" and were statistically processed in order to determine the variability within the populations, but also the correlation c...

The aim of this paper was to investigate the effect of defatted rapeseed flour addition from which proteins were extracted (DRF) on quality characteristics of bread as a finished product by baking test, rheological and microstructural examination. The dough rheological properties were determined by using the Alveograph device and its microstructure was analyzed by using the epifluorescence light microscopy (EFLM). Also, there were conducted analyses on the bread quality prepared from composite flour (wheat flour 6...

The Pectobacterium bacteria are classified among the most economically important pathogens for growing potatoes. In recent years, an increase in diseases caused by these bacteria could be observed. The purpose of this work is the study of the antibacterial activity in vitro of five plant extracts namely grains of black cumin (Nigella sativa L.), cloves (Syzygium aromaticum), Eucalyptus camaldulensis, wild carrot (Daucus carota L.) and thyme Numidia (Thymus numidicus), against the strain Pectobacterium collected in...

Urban areas face the problem of traffic congestion. City Centers are the destination of many people traveling to work, school or business every day. The spatial structure of a city is not fixed in space, but is subject to constant transformations associated with a vast array of social, economic and environmental processes. One of the processes that we can observe in Polish cities is the increasing number of parking spaces. In the urban planning of the development of large Polish cities, the trend of reducing car t...

The purpose of the study was to present detailed the stages in achieving the documentation necessary to upgrade the infrastructure of a road, after the landslides which led to the erosion of embankments. The chosen methodology consisted in designing and analyzing the topographical, geological, hydrographic, climatic studies and seismic classification of the area. Following the completion of basic works were proposed other works necessary to remedy the problem, conjunction with legislation to obtaining the Environm...

The removal of sulphate ions from different types of wastewater is an environmental challenge faced by several industrial sectors, such as the mining, petrochemical or metallurgical industry. Sulphates and heavy metals represent one of the main pollution sources is industrial effluents such as acid mine drainage (AMD) and other mining effluents. Manufacturing processes, primarily mining activities, often result in the production of effluents containing high amounts of inorganic pollutants e.g. heavy metals or sulp...

Pyrite is one of the main rock-forming components for Upper Jurassic-Lower Cretaceous black shale Bazhenov Formation. The correlation between pyrite and total organic carbon is found to be relatively high; however, some deficiencies of this hypothesis are discussed. Interlayers with high pyrite and low total carbon contents are encountered in the transition zone where the Bazhenov Fm. grades into Podachimov pack and into the underlying Georgiev Fm. The presence of pyrite in such layers is associated with the diage...

The article describes studies of the process of mineral raw refinement in dry, wet form and with addition of chemical reagents. Specific energy spent to refinement has been determined in the course of disintegration, as well as specific surface of particles before and after refinement has been measured. The values of refinement of inter-phase surface area of disintegrated mineral particles and values of specific surface energy have been calculated. With the help of performed studies one may obtain quantitative exp...

The most appropriate way to increase grip of bitumen with mineral materials is the use of adhesive additives which are slowing down the process of aging of bitumen due to oxidation and increasing durability of pavement. Adhesive properties of bitumen are important characteristics, as they are having a huge impact on operational properties of composite materials, such as asphalt mixtures. To understand the chemical behavior of the binder components interaction and improve adhesion to mineral components of asphalt c...

The current problem of the last decade in the world is the increase of oil production volume due to the extraction of its hard-to-recover reserves. The difficulty of its extraction is determined not only by the petro-physical characteristics of the oil-bearing formation, but also by the physico-chemical properties of the fluid itself. However, not all methods of enhancing oil recovery are ecologically safe. The most effective and ecologically-friendly method of soil purification from pollution by oil products is t...

The paper deals with the theoretical and practical analysis of the influence that the cutting direction of the bucket wheel excavator has on the digging forces acting on the wheel. Usually, when the terrace cut technology is applied, the bucket wheel of the excavator cuts vertical chips where mainly the perpendicular to stratification digging method is predominant. All the laboratory trials - done on the test rig - were conducted mainly for this type of vertical chip cutting. In cases when the drop cut method is a...

The efficiency of bioscouring treatment applied on 50 % of flax + 50 % of cotton material by determination of the residual Ca2+ was studied. The treated samples were analyzed using a spectrophotometric method based on the measuring of the colour strength [K/S] of the bioscoured material after dyeing with Ruthenium red and Alizarin. The reflectance (R %) at 540 nm was measured and [K/S] values were calculated [1, 2]. The purpose of bioscouring was the removal of morphological impurities present in the cotton and fl...

The paper starts with the presentation of some general elements for characterizing, from morphological, geological, climatic, rainfalls and hydrographical point of view, a national road routing, highlighting the specific particularities which are concerning the study of the instability phenomena. Further on, are presented the types of instability phenomena present on the national road routing, including the general causes that produced them. The paper ends with the analysis of two case studies, considered as being...

One of the common applications of geosynthetics is their use as reinforcement for aggregate and soil layers. Geosynthetics improve the mechanical properties of the reinforced layers, which are originally, due to various reasons, insufficiently protected. Therefore, the use of geosynthetics allows for bearing heavier loads thanks to the soil-reinforcement system and an extended material durability. This article describes the laboratory tests of mechanical properties of a hexagonal geogrid made of polypropylene used...

Based on a real-life example, the report presents the methodology and the process of adapting in situ measurements from static CPTu probing for an application in a design process, using direct methods of driven pile capacity estimation. The report discusses two approaches. One of them is based on a real-life original CPTu measurement involving preliminary soil assessment while the other one is based on the initial averaging of the measurement values qc and fs. The paper provides methods of averaging cone resistanc...

The influence of ultrasound energy on bioscouring treatment applied on a 50 % of hemp + 50 % of cotton woven fabric was studied. The aim of the bioscouring treatment was the removal of the natural cellulose attendants for better fabric properties. The treatment conditions were: variable concentration between 1-3 % (o.w.f.) of the commercial enzyme product Beisol PRO, which is a mixture of pectinases from Bezema Company, Switzerland, 2 g/L of the complexing agent EDTA, 0.5 % of wetting agent Denimcol Wash RGN, phos...

The bakery industry has gone through a revolution in the last 150 years. Small handmade bakeries existing in almost every village are giving place to highly technologized bakery industry since it is considered that the bread made this way is more efficient. Productivity has become the key of success this period of time. New baking technologies have been developed to comply better with the new demands of the market. In the present context, the main goal of this paper was to investigate the impact of different bakin...

In food industry water is used as a raw material, as a solvent for substances with different density when washing products and equipment, as transport water or merely cooling water.Quality monitoring of the hygienic drinking water and the waste water discharged is one of the conditions requested for all producing, processing, storing, keeping, shipping and marketing product supply units. The increase in acquisition, application and development of knowledge, advanced services and techniques in the fields of environ...

Acoustic or phonic pollution is a type of noise pollution caused by noises, a complex of non-periodic sounds with random disagreeable insurgency that affects the psychological and biological state of human and animal organisms. The physical or objective characteristics of the noise are the strength or sound intensity (which depends on the features of the source, the distance and the possibilities of transmission or multiplication), duration and frequency. For the determination of the noise level, sound-meters, whi...

The major changes that have taken place over the last decade on the world food market reveal peopleпїЅs great interest in health and nutrition. The modern consumer is being warned about the major influences that the diet has on his health condition by the appropriate information accompanying the well-packaged product or by publicizing the risk of some diseases whose major cause is an unbalanced diet. Since there is great interest in providing bakery products with preservation by complying with the clean label stat...

Multicolored asian ladybird Harmonia axyridis Pall. is a well-known aphid predatory species, of Asian origin. The species is classified taxonomically, at present, in the tribe Coccinellini family Coccinellidae. The species is considerate bivoltine, but may submit up to 5 generations/ year. The main role of the species is its use in biological control. A negative impact on potential benefits that accompany this coccinellid would be predation insects native to the same family. Current status of invasive species is t...

The paper analyzes physicochemical properties of liquid products of waste tyre pyrolysis, and attempts to assess their usefulness as fuel for diesel engines. Every year, the number of produced vehicle tires increases at a very fast pace. Used tyres turn into waste that is difficult to manage simply because, according to relevant EU regulations, vehicle tires should be subject to recycling. To a large extent, the problem of waste tyres management may be resolved by their utilization through pyrolysis. The processin...

The article presents results of using vibratory jaw crusher for feed preparing for the granulation process. The main aim of the study was to determine the possibility of preparing the limestone feed for non-pressurized granulation process by means of very fine crushing in the laboratory vibratory jaw crusher KW 40/1 with kinematic actuation of jaws. The crusher is characterized by high average degree of fragmentation (30-50). The study was conducted in two stages. The first stage included experiments with vibrator...

Jiu Valley represents one of the most important areas for coal mining in Romania, thus industrial development has generated a high level of health and safety at work issues. At work places in mining industry, the staff of the woodworking workshops is exposed to various concentrations of dust, possibly leading, in time, to occupational illnesses. Thus, wood processed in mining unitsпїЅ workshops is utilized for temporary support of coal faces, wrapping underground mining, insulation dams, ventilation doors, etc. Th...

Developing products modified structurally and functionally that ensure health benefits is relatively recent and is the result of accepting the idea that food plays an important role in the prevention and therapy of some health conditions; these arguments are at the basis of the appearance of пїЅfunctional foodsпїЅ with пїЅhealth benefitsпїЅ. Modification techniques of non hydrogenated palm oil lipids (simple mixing, hydrogenation, interesterification, fractionation) are no novelty since they are being optimised th...

This paper presents a study of the structural models convergence, rezulted from CAD (Computer Aided Design ), based on method of estimation. The study of the structural models convergence presented a method based on the convergence, in the sense of mathematical analysis, adapted to finite strings. The convergence estimators are status sizes that characterize the response of the structural model to the given load. As convergence estimators can be used sizes that characterize the response of the structure, like foll...

This paper presents the diversity of parasites species identified on cultured fish species, the degree of infestation and the epizootological state in nine fish farms (most of them producing fish fry for stocking other fish farms). These farms are located in five counties in the south of Romania (Arge?, DпїЅmbovi?a, Teleorman, Giurgiu and C?l?ra?i). A total of 653 fish were investigated. The fish species belong to two fish families namely Cyprinydae: Abramis brama, Cyprinus carpio, Carassius gibelio, Hypophthalmic...

Sea buckthorn (Hippophae rhamnoides L.) has gained worldwide researchers attention as a unique and valuable plant, primarily for its medicinal and nutritional potential. The berries can be capitalized by their processing in order to obtain derived alimentary products such as, e.g. juice and jam, as well as used for flavoring of dairy products. The dried sea buckthorn berries and leaves are used for tea. Lately, due to the fact that consumers are more open to information, so their level of awareness is higher, ther...

This investigation is aimed to determine general development patterns of the natural and climatic situations and lakes of the boreal zone in the later and postglacial time in the southeastern periphery of the Fennoscandian crystalline shield since the time of the last deglaciation. The analysis of the subfossil Cladoceran community was carried out on the basis of the 23 samples of Lake GahkozeroпїЅ bottom sediments in the Republic of Karelia. In the subfossil Cladoceran community of the lake 42 taxa have been iden...

The solution of subsoil-structure interaction is affected by several factors as a choice of interaction model, influence of physical-nonlinear behaviour of structure and co-effects of the upper structure and the foundation structure. The subsoil-structure interaction can be solve by application of analytical methods or numerical methods - eg. Finite Element Method (FEM) or Boundary Element Method (BEM). FEM was used for numerical analysis performed in this article. Many different interaction models implemented in ...